Replacing the original hard drive was quick and easy, and the improvement in performance was obvious and profound. It also allows you to clone a larger capacity drive to a smaller Samsung SSD.In late 2014 Amazon had a great deal on the Samsung 840 EVO SSD, and I took the opportunity to upgrade my aging MacBook Pro with it. Samsung Data Migration (SDM) is a data migration software that allows you to transfer over all existing files and programs from a current HDD or SSD to a new Samsung drive such as Samsung 850 EVO SSD, Samsung 840 Pro SSD, etc. Samsung Data Migration review.Unfortunately, the next challenge was to figure out how to install it.This item Samsung 840 EVO 500GB 2.5-inch Basic SATA Solid State Drive Samsung 870 QVO 1 TB SATA 2.5 Inch Internal Solid State Drive (SSD) (MZ-77Q1T0) Samsung SSD 870 EVO, 500 GB, Form Factor 2.5, Intelligent Turbo Write, Magician 6 Software, BlackBest recording software for mac. As a Mac user I naturally waited until the Mac version came out and fortunately it became available for download a few days before the end of October. The bug fix came out in October 2014, first as a Windows application, and with a Mac/Linux version promised by the end of October. Soon after, I read on Anandtech that Samsung acknowledged a serious performance bug with the 840 EVO SSD that would dramatically slow down read performance for data that had not been rewritten in a while.
Samsung Evo Solid State Drive Data Migration Software Mac OSX And UsingI successfully applied firmware update EXT0DB6Q to my 840 EVO using the same CD technique I describe later in this article (“ Creating a bootable optical disc with the fix on it”). Mac users should note that the linked PC Perspective article says the ISO image can be installed on computers without optical drives using “a tool such as Rufus.” Getting the softwareAccording to the Internet search result, Samsung data migration software for the EVO Series and PRO Series SSDs is the most wanted. Before making any modifications create a backup via Time Machine, in case of emergency there is a backupIt may be helpful to refer to an earlier version of this guide, written using older versions of Mac OSX and using the older Cloning software, which is archived.Update: (April 28, 2015) PC Perspective reports that Samsung has released another firmware update EXT0DB6Q, with a downloadable ISO image for Mac users, to try and finally resolve the 840 EVO performance problem after it turned out that the first update didn’t completely work. This new version EXT0DB6Q is more recent than the version installed by the software in this article. Option 1: Clone hard drive to SSD. There are different approaches.But the Mac version does not run under OS X, so you can’t use any solution that involves a drive that boots into OS X. While the Windows version is a point-and-click Windows application that lets you use the computer while it works in the background, the “Mac/Linux version” is actually a command line utility and has to be installed on a CD or USB drive that you can boot the Mac from. It has apparently been replaced by the new firmware noted in the other Update above.But the Mac updater came in a form I didn’t expect. SSD 250GB (OS Software RAID-1) Samsung 970 Pro m.2 NVMe SSD x2 (ZFS l2arc.You can download the Samsung software from the Samsung SSD Downloads web page.Update: As of April 23, 2015, the Samsung SSD 840 EVO Performance Restoration Software section has been removed from the Samsung software page. The software use issues.SSD, also know as solid state drive (and non-mechanical HDD) memory to store. Here are some common situations about Samsung Data Migration errors. You have to find the bootable USB flash drive software and figure out how to put it together on your own. A little more research revealed that you can’t boot a Mac from a USB flash drive unless it has the right EFI boot loader on it, and that isn’t included with either the Samsung updater or FreeDOS. After looking up various instructions on the Web I was able to use Terminal to copy the image to a USB flash drive I formatted as MS-DOS FAT, but the drive was not visible in the list of volumes you get when you hold down Option while starting up a Mac, even after I found FreeDOS and added that to the disk image. It contains only the Samsung utility, no bootable operating system of any kind. But the Samsung “Bootable USB disk” version isn’t actually bootable on a Mac from a USB flash drive. (Almost) creating a bootable USB flash drive with the fixI first thought I could just download the “Bootable USB disk” version of the software (Samsung_Performance_Restoration_USB_Bootable.zip) and image it onto a USB flash drive. (A couple months ago I successfully used the Terminal to copy another company’s DOS software onto a USB flash drive that did boot my Mac, but that’s because that company first made sure their disk image had everything necessary to boot a Mac. Basically this means if you don’t have the technical expertise to set up your own bootable USB flash drive, which usually requires Terminal commands, you’re out of luck with the USB flash drive option. 2) For assistance on completing this step, please refer to USB boot utilities from a trusted internet site.Thanks a lot, Samsung. Bonus points if it can be done with point-and-click (not Terminal) steps!Update: Here is a possible solution. If you know how to easily use OS X-based tools to create a bootable USB flash drive that can load a DOS-based (not OS X-based!) updater, or at least how to modify the Samsung or FreeDOS disk images so that the Mac can boot off it and the Samsung software will run, please post your instructions or links in the comments at the end of this article. And I was thinking of all those other users who never even go near the Terminal: What should they do?This is where I’ll ask for your help. Permanent header in my word document for macThen I got ready to burn the Samsung ISO image to the disc. I grabbed an old CD-RW (others have successfully used a writable DVD) and used the Quick Erase feature of Apple Disk Utility so that I could reuse it. Creating a bootable optical disc with the fix on itMy MacBook Pro is old enough that it still has an optical drive, so I decided it was time to try the bootable optical disc option instead. Also, readers are starting to add ideas to the comments, so check there too. Dmg extension, Disk Utility will make the optical disc identical to the contents of the disk image, which is what you do want. But when the disk image has a. Rename the disk image filename extension so that the filename reads:If you don’t rename the disk image, Disk Utility will just burn the single unopened ISO file onto the disk, and that’s not bootable. At the Samsung downloads page, download the “Samsung_Performance_Restoration.iso” disk image. The only software you need is Disk Utility, which is already on your Mac. Back up the entire drive. So before you get started: ( Update: Unlike the Samsung Performance Restoration software that is no longer available, the currently available EXT0DB6Q firmware updater only takes a minute or two to run.) It shouldn’t erase data, but with an operation like this you never know. Running the updateDepending on the size of your SSD the update process may take an hour or two, and once you start it you must not interrupt the process. Put the blank optical disc in the optical drive and finish burning the disc. When you’re done it should look like this:You can then continue below. If FileVault is turned on, turn it off. If it’s a portable Mac, be sure it’s plugged into AC power since the process could take a long time to complete. Run the fix only when you won’t need to use the computer for a few hours. (You should also be able to boot directly into a CD or DVD by holding down the C key as the Mac starts up.)From this point on, the Samsung Performance Restoration utility takes over and works pretty much as it says in the Installation Guide. Select the volume with the update on it (in my case the CD) and press Return. This displays the list of connected bootable volumes. Read the section “General Limitations” in the software’s Installation Guide for additional cautions.To use the bootable media, insert it and then restart the Mac while holding down the Option key. (An OS X user account password is OK, you don’t have to remove that.) ![]() ![]()
0 Comments
Leave a Reply. |
AuthorTerrell ArchivesCategories |